1981 Golf GTI Project Car Progress Page
01/06/02 Engine parts are coming from South Africa and should arrive with 4 to 6 weeks, other parts have been gathered from the UK. My block has now been stripped in preparation for being balanced and blueprinted.
02/06/02 Removed the front spoiler today and discovered that it was held on with tape and a couple of nails! The spoiler is an original VAG part so I'm going to repair it properly - the car looks strange without it.
07/06/02 Today I found that my flywheel that I thought was a 210mm is actually a 200mm, therefore my new clutch will not fit! I have ordered a 210mm flywheel from South Africa which will arrive with the rest of my parts. It will need to be lightened once it arrives but hopefully this won't hold up progress too much.

08/06/02 Replaced rear suspension bushes, bump-stops were worn beyond recognition but I hadn't ordered any of these so for the mean time the car is running without bump-stops!
I also found that the bilstein shocks are complete units, not inserts. Perhaps they are shortened like my Jamex struts. They look to be in good condition and they also have an adjustment on the bottom of the front shocks. I don't believe that bilstein ever made springs so I'm not sure what springs the car has. When I get a chance I will give the car a degrease and steam clean to get a better look. I ran out of time to do the front suspension top mounts but I will get this done soon. I also noticed on the way home that there was a ticking noise coming from the fusebox area. If the car had a radio I wouldn't have been able to hear it but it probably means that one of the relays has a problem - I'm guessing its something to do with the fuel pump relay. I didn't get a chance to sort this out as it was getting dark and tomorrow is a track day that we can enter in at Manfeild. I won't be driving in it but I will be doing the video work.
21/06/02 Removed more unnecessary wiring from ignition switch area. The alarm that was once installed was removed some time ago but the wiring remained. The was a strange setup with a relay hanging off the ignition switch and several other wires. I removed all the wiring that isn't original and then tried to start the car - it started but the lights / fan / gauges did not work. I reconnected a wire that runs from the rear of the fusebox to the switched part of the ignition switch and everything is normal again. I will sort this out properly at a later date but for the moment I just want to the car to run so that it can be worked on easily. While looking at the fusebox I try to find the clicking relay that I spoke about above. The fuel pump relay has been played with. I removed it and the car still starts and runs as normal! There is a lot of extra wiring around the fusebox so I won't attempt to alter it at this stage.
24/06/02 I got a couple of quotes from panel beaters today. They were higher that I expected but at least the car will look more respectable for its first race meeting. It is booked in on the 8th of July.
25/06/02 I have found a company who makes roll cages for a reasonable cost and I will go and see them next week when a friend takes his Lancia Delta Integrale to them to have a cage installed.
26/06/02 My block is ready to be installed and is waiting on the floor of the workshop for the head to arrive from South Africa. I also put the spoiler on the front of the car after repairing it and making it black again instead of a dull grey. The front panel of the car where the spoiler attaches to is bent and the spoiler is therefore a bit twisted but this will be fixed at the panel beater / painters.
02/07/02 Today I started stripping the car ready for painting. I need to remove the front and rear windscreen as well as the right-rear side window and all the trim inside and out on the drivers side. The drivers side, roof, boot and bonnet are the only areas that are going to be painted at this stage. I will hopefully have the car back on the road by next Friday.
04/07/02 I finished stripping the car today and managed to remove both the rear windscreen and the rear side window myself without any special tools. I left the front windscreen in place as it is chipped and I would most probably break it. I have a spare windscreen so if it does get broken it is no big deal. I also visited a roll cage manufacturer today where they can build me a cage in around a months time. It will be a custom 6 point cage with side bars and all the necessary documentation for motorsport use.

Last pic prior to painting.