1. THEMA : Wall and Floor Tiling
2. OBJECTIVES : Mapping storey level ability of participant through examination of result work installation/ tiling at wall and floor.

 

3. DESCRIPT OF COMPETITION;
1. Technical Competency/ Knowledge :
1. Reading job size measure and picture
2. Analyze requirement of materials and equipments
3. Formulation of active stroke which are effective and efficient
4. Preparation and planning Layout of tiles
5. Tally each every materials type
6. Measurement arrange situation and amputation of materials
7. Election of working safety appliance productive/skills competency
2. Productive/Skills competency
1. Drawing to arrange Layout
2. Arrangement and making of appliance assist activity
3. Lay Out Place of tiles
4. Preparation and truing of substrates
5. Symmetrical and balance of tile work
6. Wall tiles floor and Installing
7. Decorating tiling of surfaces with tiles mosaics
8. Cleaning and grouping of tiles
3. Attitude and SOP :
1. Using the Technical procedures
2. Standard Operational procedures care
3. Treatment the tools safety
4. Work management
5. Calculating the quantity and quality of the material
4. Time Schedules :
1. Wall Tiling = 9,5 hours
2. Floor Tiling = 10 hours
4. EVALUATION
1. WALL TILING = 100 POINT

 

NO	ASPEC EVALUATION	REMARK TO MEASSURE
01	Elevation at the bottom/ basic to the top of the tiling wall	The elevation of the tiling wall, note the max. tolerance
02	Dimension of tiling wall ( height and width )	Measure the two vertical edges, evaluate the maximum tolerance
03	Verticality of the tiling surface	The 2 ends of the tiling wall , evaluate the tolerance
04	Leveling of joints	The top joint and the lowest one of the tiling wall
05	Flatness of surface	The two diagonal of the tiling wall
06	The thickness of joint	The thickness of the joint
07	Perpendicularity of the two tiling surface	The angle at the top and the foot of tiling wall
08	Solidity of the tiling	Knock by a hard wood to check the unsolid tiles
09	Joint analigment	Stretch a string along the cross joint and the horizontal
10	Joint cleaning ( regular Joint & Clean surface )	Evaluate by observation and hand
11	Drawing the star	This will not be marked if the drawing is not finished
12	Time and productivity

2. FLOOR TILING 100 POINT

 

NO	ASPEC EVALUATION	REMARK TO MEASSURE
01	Elevation Of floor tiling surface	The elevation of the tiling floor, note the max. tolerance
02	Dimension of tiling floor ( height and width )	Measure the length and width edges of floor, evaluate the maximum tolerance
03	Flatness of the tiling surface	The 2 ends of the tiling floor , evaluate the tolerance
04	Leveling of joints	The top joint and the lowest one of the tiling floor
05	Solidity of the tiling	Knock by a hard wood to check the unsolid tiles
06	Joint analigment	Stretch a string along the cross joint and the horizontal
07	Joint cleaning ( regular Joint & Clean surface )	Evaluate by observation and hand feeling
08	Drawing Map and star	This will not be marked if the drawing is not finished
09	Time and productivity

5. REQUIREMENT FOR COMPETITORS
1. The product of the competitors must be done according to the drawing and the technical requirement
2. Competitor must check the material , they can ask for change 10 minutes prior to commencing the competition if there’s same thing wrong
3. During the competition, competitors must read the drawing themselves. They are not allowed to talk each other.
4. When the time is over , competitor must stop working and ,after marking competitor must clean
6. MATERIAL

 

WALL TILING	FLOOR TILING
Tiles = 200 x 250 mm	Tiles 300 x 300 mm
Cement and sand mortal 1.00 #	Cement and sand mortal 1.00 #
White Cement	White Cement