Facilities Maintenance Test
Questions
- In thread specifications 10-32-1blh, how many threads per inch are there?
- Ball bearings and roller bearings are called?
- The ampere is a unit of electrical?
- Romex is a?
- If part of a circuit is connected to a metal frame it is said to be?
- Sweated joints are?
- A union is a fitting that?
- Any substance that can flow is called a?
- 50-50 solder is 50 percent lead and 50 percent?
- The single most important factor for success in applying a protective
coating is the?
- Which class of fire-fighting chemicals should you use to combat a live
electrical fire?
- When using a steel ruler, you should make your measurement from the?
- For heavy duty line cleaning of a drain, you should use a?
- A trap spoon is for?
- A plum bob is used for?
- Trowers are used for? (I bet they meant trowels here.)
- What is the first step in installing a flared fitting?
- When selecting saber saw blades, you should select the _______ blade that
will do the job.
- What should you do if you find water in oil taken from a gear drive.
- A wide channel cut in a material is called a?
- Frequent slipping of a brake or clutch usually indicates?
- If you discover a chemical spill, you should clean it up only if you have?
- A burned spot in a V-belt probably indicates?
- OSHA�s hazardous communication standards requires chemical manufacturers
and distributors to?
- A mechanism used to open or close a valve is called?
- The purpose of the grounding wire in an electrical tool is to protect
against?
- What type of wrench is normally used on large-diameter pipes and on 3" or
more diameter?
- You should operate a forklift only if?
- In a properly wired electric circuit, the hot wire is always?
- If you touch someone who us in contact with an electrical source, you
will?
- A ground fault can be defined as?
- Class B fires involve?
- A flammable-liquid fire should be put out with an extinguisher that shows
a?
- An indication that a machine may need maintenance is?
- Which of the following is a basic tool for electrical troubleshooters?
- Of all the HVAC components ________ need the most attention?
- Which of the following wires can carry the largest current?
- Practical machine maintenance includes?
- One of the most frequently performed PM jobs is?
- How often should you inspect an evaporative condenser�s air intake for
unusual restrictions?
- When mounting a ball or roller bearing on a shaft you apply force to?
- Fan impellers must be cleaned regularly to keep them from?
- Air filters are usually packed so that _________ is (are) filtered.
- An absolute air filter?
- A valve with one inlet and two outlet ports is called a _________ valve.
- A ratchet typically works in combination with?
- When using a hacksaw, you should press the blade against the work on?
- Who is responsible for inspecting power tools before each use to make sure
they are in safe working condition?
- Which kind of lock washer provides the most positive locking?
- A lubricant�s physical state can change if there is a change in the?
- The most important property of a lubricating oil is its?
- Lubricant�s used in cold weather must have a low?
- The best way to apply dry-film lubricants is by?
- Lubrication management can lead to a large reuction in costs arising from?
- Solid couplings are not often used for joining shafts, because they
require?
- The most common type of mechanical clutch is the _______ type.
- When multiple drive V-belts are made together in the form of one common
belt, they are called?
- The gear ratio of a speed reducer equals the?
- In general, when should you check a speed reducer for noise, oil leaks,
and hot bearings?
- The most common kind of electric motor used in industrial application is
the?
- To keep lubrication in and dirt out, plain journal bearings may have?
- One of the greatest causes of rapid and excessive wear in bearings is?
- The three basic shapes of roller bearings are?
- The first rule in keeping contaminants out of bearings is to maintain?
- A pump that operates in a back and forth, straight-line motion is called a
__________ pump.
- What sizes of pipe are ordinarily designated by the O.D.?
- The most corrosion-proof drain pipe is made of?
- What are the two major classes of plastic pipe?
- What is the name of the component that carries fluid through a 180 degree
turn?
- The part of a valve connected directly to the piping is called the?
- What type of valve permits fluid flow in one direction only?
- The purpose of a filter in a hydraulic system is to?
- When a filter in a hydraulic system becomes dirty you should?
- One problem with hydraulic hoses is that they?
- Before adding fluid to a hydraulic system, you must make sure the new
fluid is?
- In general, you should replace or clean the filter elements in a hydraulic
system at least every?
- An air compressor raises the pressure of air by?
- When you disconnect an air hose with quick-disconnect couplings.
_____________
- According to federal law, the nozzle pressure of an air hose used to blow
chips away may not exceed?
- What is generally illustrated in a schematic drawing?
- The amount of heat required to raise the temperature of an object by 1
degree is called ______ of the object.
- Fuses and circuit breakers protect an electrical circuit from?
- Insulating materials? ___________
- Which gauge number indicates the largest wire?
- The watt is the standard unit measure for? _______
- To obtain six volts from a combination of 1.5-Volt cells, you need _____
cells connected in __________.
- The positive and negative electrodes in a storage cell are connected to?
- The capacity of a battery is measured in?
- A switch with three terminals and two positions is a?
- The electronic device used to convert AC to DC is a(n)?
- Electric power is measured in?
- The neutral wire in an interior circuit must be?
- The purpose of soldering a joint is to?
- The most commonly used grounding method today is?
- One function of the ballast used with a mercury-vapor lamp is to?
- A universal motor that runs at two or three different speeds, but not at
the speeds in between, is called a(n) ___________ motor.
- The most common voltage changes used in industrial motors involve?
- Lubrication of motor bearings should be done when the?
- Interchanging any two supply leads of a three-phase motor?
- Normal failure of a flourescent lamp is indicated by?
- The best way to tighten a V-Belt and take up normal stretch is by means of
a(n)?______
BACK TO TROY'S FIX-IT
PAGE