Project Remington TACS M-9 I am going to get a UHC Super 9 Pro sniper rifle, and I am planning on upgrading it into a Remington TACtical Sniper Model 9. Here is what the stock gun has:

UHC Super 9 Pro Sniper Rifle
-130-150’ effective range
-Matte Black synthetic stock
-No scope mounts
-Iron sights
-Thin metal barrel
-No HOP-UP

Remington TACtical Sniper Model 9
-150-175’ effective range
-Matte Black synthetic stock with weights
-After market scope mounts
-3-9X40mm scope
-BULL Barrel
-Sound Suppressor
-HOP-UP barrel
-APS-2 SV stock spring

Remington TACtical Sniper Model 9 Advanced 1
-Install a Harris Bi-Pod
-Modify the stock to make it adjustable
-Install a Tight-Bore Barrel
-Extended Magazine

Remington TACtical Sniper Model 9

Matte Black Weighted Stock
This is a simple matter of removing the stock from the gun, and spray painting it matte black. I will then allow it to dry for a week or two. After it has finished drying, I will install weights into the fore end of the stock, and seal it with epoxy.

Scope Mounts
There are several ways of doing this. One of the most common ways is to use a Dremel to cut out scope mounts from the plastic bases, but this makes the mounts too weak to handle a heavy scope. So, I am simply going to get some metal scope mounts for the Super 9 Pro, and mount them on, for these will be strong enough to withstand the 3-9X40mm scope’s weight.

BULL Barrel and Sound Suppressor
The BULL Barrel and the sound suppressor will actually be one tube. Not only will it stabilize the barrel by adding weight, but it will silence it. This is a simple matter of buying a large diameter aluminum tube, creating baffles and suppressor caps, and piecing it all together. I’ll add a diagram later.

Remington TACtical Sniper Model 9 Advanced 1

Harris Bi-Pod
Installing a bi-pod should be quite easy. I heard that the stock sling studs and swivels aren’t too nice, so I am going to install my own by drilling a hole in the forend of the stock, and installing the swivel. I will then attach the bi-pod.

Adjustable Stock
For this I shall just make my own stock piece out of wood, attach rubber to the end of it, and drill holes at the butt stock. In these wholes, I will put two nuts that two other screws will go into. Then I will drill holes in my custom stock piece, and attach the screws onto it. I’ll add a diagram for these later.

Tight Bore Barrel
This will be a little more complicated. The stock barrel’s diameter is 6.20mm: not good for a sniper’s needs. So, I am going to attempt to find a matching AEG or springer barrel for this one, and possibly have it longer, because if it was, it could just fit inside of the longer BULL Barrel that I would make.

Extended Magazine
This is for cosmetic purposes only for now. I want to give it a tactical look, and try to make it look unique in the bolt-action airsoft gun lineup. For this, I will have an M16 or FAMAS magazine. I will attach it to the stock magazine somehow, and, possibly in the future, link it up to the gun for a larger capacity, such as 10, or, maybe even 15.

Upgrades/Accessories

Stocks
Model 700 Style Wood Stock-¥42,000
Synthetic Stock with Square Cheek Rest-¥25,000

Scope Rails
    JP Stainless Steel Slotted (14) Weaver Rail-¥1,800
    JP Metal Slotted (14) Weaver Rail-¥1,800
    KM/Head 19.50 Dovetail Rail-¥900
    KM/Head 19.50 Weaver Rail-¥900

Pistons/Spring Guides
    JP APS-2/Super 9 Gold Colored Piston and Silver Spring Guide-¥4,700
    JP APS-2/Super 9 Aluminum Piston and Spring Guide-¥3,800
    JP Aluminum Piston-¥2,000
    JP Black Aluminum Piston-¥2,800
    JP Short Aluminum Piston-¥2,300
    JP Long Aluminum Piston-¥2,700
    JP Long and Thin Aluminum Spring Guide-¥1,100
    JP Short and Wide Aluminum Spring Guide-¥1,200
    JP Two Short Aluminum Spring Guides-¥2,300
    KM/Head 19.50 Colored Aluminum Piston and Guide Sets-¥2,600

Accessories
    Sound Suppressor-¥5,800
    JP Metal Bolt Handle-¥5,500
    JP Stainless Steel Bolt Handle-¥7,000
    JP Brass Trigger Mechanism with Finger Pad-¥3,900
    JP Brass Trigger-¥3,200

Here is the price guide for all of my materials:
UHC Super 9 Pro Sniper Rifle-$85.00
JP Metal Slotted (14) Weaver Rail-$18.00
JP APS-2/Super 9 Aluminum Piston and Spring Guide-$38.00
Matte Black Spray Paint-$2.00
Leaper’s 3-9X40mm Full Size Scope-$32.99
Weights-Not sure yet
Colt M16A2 Magazine-$30.00
Two Inch Wide Aluminum Pipe (Ten Feet)-$5.00
Harris L Model Bi-Pod-$49.95

Total-$260.94

Smurfett

Hosted by www.Geocities.ws