Trabalhos Publicados
1. “Technical Progress of the
Soviet Steel Industry”. Journal of the State Engineering Corporation of Ceylon, 1970.
Abstract
In the post war years
there has been a marked technical progress in the Soviet Steel Industry. The
demand for steel is ever increasing and attempts are made continously to
produce quality steels at reduced cost. Much attention is laid on Research and Developmet and most Steel Plants
exhibit excelent technical and economic indices. Latest metallurgical
techniques are used where ever possible. For example intensive usage of Oxygen
and Natural gas, modified furnace designs, standardisation of charge material,
use of self-fluxed sinter improved Refractories, continous casting,
mechanisation and automation are some of the factors responsible for high
productivity in the Soviet Steel Plants.
2. “The effect of slab to plate deformation ratio on property
directionality of ESR and continuosly cast steels”. The Metals Society Meeting
“Directionality of properties in wrought products”, 27-28 Nov. 1974, London.
By utilising the
E.S.R process to effect controlled ingot solidification, in conjunction with a
marked reduction in the volume fraction of inclusions, particulary sulphides,
plates have been produzed in both pilot and commercial plants, exhibiting
exceptioinally high absolute values of ductile Charpy V-notch shelf energy, and
through-the-thickness tensile ductility. During trials a 5.4 tonne E.S.R. slab,
subjected to a deformation of 80%, has been produced which has been virtually
isotropic, for example, the values in the L, X and Z directions de Yield
stress, U.T.S. and %R of A were 624, 621, 623 N/mm2 and 734, 731,
738 N/mm2 and 76, 77, 74% respectively while the ductile Charpy
V-notch shelf energy and 50% F.A.T.T. were 225, 230 Joules and -145, -145ºC in
the L adn X directions respectively. The influence of rolling deformation from
cast slab to plate has been examined using as criteria the anisotropy of Charpy
V-notch and tensile properties. This work has included an examination on trial
plates rolled from various continous slab casting plants. Regression equations
have been derived for Charpy shel energy and F.A.T.T in the L and X directions
of continous cast plate. The basis for the change is examined to asses the
contribution of inclusion type, size and distribution and change in
microstructure with increasing slab to plate deformation.
3. “Low carbon steels for plate applications”, Institution of
Metallurgists, Spring residential course, Series 3, Nº 6, March 1977, London.
Abstract
BSC experience is reviewed for the production of a range of high quality controlled rolled structural and linepipe plate steels suitable for the X60 strength level and above. Factors controlling the toughness of the steels, as determined by Charpy transition temperature, Charpy self energy and Battelle transition temperature are examined. Properties available from the very low S continously cast and the low S Rare Earth Metal treated ingot routes are discussed. Property levels in the low C controlled rolled product are compared with the strength and toughness obtained in similar low C steels processed by other routes and with steels at higher, more conventional levels.
4.
“Análise
de distribuição de temperatura durante a laminação”, ILAFA, Congresso
Internacional, Rio de Janeiro, Brasil, Maio, 1980.
Resumo
Para o cálculo
de carga em laminação a quente, é fundamental o conhecimento da distribuição de
temperatura ao longo da espessura do material que está sendo processado. Tal
gradiente influencia na resistência á deformação e, portanto, nos parâmetros
tais como força de laminação, torque e potência. Este trabalho desenvolve um
modelo que permite prever a distribuição de temperatura em qualquer instante do
processo. Para isso são considerados os mecanismos de transmissão de calor que
intervêm durante a laminação. Este modelo foi comprovado experimentalmente em
escala piloto e industrial, sendo posteriormente utilizado para cálculo de
carga de laminação e na elaboração de um esquema básico de controle por
computador de laminação de chapas grossas da USIMINAS.
5. “Bauschinger effect in APIX60 Linepipe Steels”, Metals Technology, Nov.
1982, Vol. 9, p. 440-445.
As part of a
programme to evaluate changes un mechanical properties occurring during U-O-E
pipe forming, laboratory tests were carried out to asses the Bauschinger effect
en 12,7mm thick, controlled-rolled Nb-V API X60 steels. Assuming a
stress-strain relationship of the form s = Coeno for the initial strain cycle, empirical
relationship are established between C1 and n1 of the
reverse cycle, with prestrain. A Bauschinger effect factor is defined por
linepipe steels, and a method is developed to calculate this factor using Co,
no and prestrain values. The Bauschinger effect was found to
increase with increasing prestrain up to ~0.03 and it was more prominent when
the reverse-flow stres was measured at small offsets (0.005) in the transient
region than at high strains, which tend to eliminate the effect. In the context
of pipe testing, the Bauschinger effect resulting from the cold
flattening-tensile testing operations is pratically unaffected by the preceding
strain cycle.
6.
“Fabricação
de Aços de Alta Resistência com Controle de Morfologia e Sulfetos”, Metalurgia
- ABM, Vol. 39, Nº 310, Setembro, 1983, p. 463-466.
Resumo
Aços de alta
resistência usados para construção de plataformas marítimas, geradores de
hidrelétricas e vasos de pressão necessitam ter excelente qualidade interna e
elevadas propriedades mecânicas quando medidas no sentido da espessura. Isto
implica na obtenção de aços com baixos teores de oxigênio total, hidrogênio e
enxofre, além do controle da morfologia dos sulfetos. Este trabalho discute os
métodos adotados pela USIMINAS para alcançar essas condições através do
processo de aciaria.
7.
“Temperabilidade
e Revenimento de Aço de Baixo Carbono e Alta Resistência - Correlação entre Microestrutura
e Propriedades Mecânicas”. METALURGIA - ABM, Vol. 40, Nº 317, Abr. 1984, p.
195-200.
Resumo
Após a realização de têmpera no intervalo de
temperatura de 820 a 950ºC, foi determinado que a temperatura ótima de
austenitização se encontra na faixa de 900-950ºC. A seguir foram feitos estudos
sobre o material na dondição temperado. Na última etapa determinou-se a melhor
temperatura de revenimento, procurando-se fazer um balanceamento ótima entre as
propriedades de resistência mecânica e tenacidade. Após revenimentos a
temperaturas de 500 a 700ºC, com tempos de permanência em cada temperatura de
0,5 a 1,5 h, o tratamento a 600ºC durante 1 hora mostrou assegurar os melhores
valores de tenacidade e resistência.
8.
“Avaliação
da Susceptibilieade de Aços API a Trincas Induzidas por Hidrogêmio em Meios
Contendo H2S e Água”. METALURGIA - ABM, Vol. 40, Nº 325, Dez. 1984,
p. 661-666.
Resumo
É discutida a ocorrência de trincas induzidas opor
hidrogênio em chapas de aço utilizadas na produção de tubos para trnsporte de
gás ácido. É revisto o mecanismo de corrosão dos tubos de aço pelo ácido
sulfídrico e água, com a consequente formação de blisters e trincas, e
apresentados os resultados do desenvolvimento de aços da classe API X-52 e X-60
para aplicações em meios contendo a referida mistura.
9.
“Efeito
de separações nas propriedades de impacto de aços C-Mn-Nb processados por
laminação controlada”, METALURGIA - ABM, Vol. 42, Nº 344, Julho 1986, p.
445-450.
Resumo
A formação de separações e o desenvolvimentop de
texturas em aço C-Mn-Nb processados por laminação controlada, com baixa
temperatura final de laminação, foram analisados. As separações causam dois
efeitos principais, quanto aos resultados, no ensaio Charpy: a diminuição da
energia para uma fratura 100% dúctil e o abaixamento da temperatura de
transição. Além disso, os aços com separações tendem a apresentar energia
crescente na região inteiramente dúctil, isto é, de patamar não bem definido.
Este efeito, no entanto, depende do teor de S do aço. A ocorrência de separação
é máxima nas vizinhanças da temperatura de transição dúctil-frágil.
10.“Método estimativo para
determinar o limite de escoamento de tubos de grande diâmetro conformados pelo
processo U-O-E com aços API”, METALURGIA - ABM, Vol. 42, Nº 345, Agosto 1986,
p. 549-554.
Resumo
Baseando-se nas propriedades de tração da chapa
original e nos parãmetros de conformação de tubos, foi desenvolvido um
procedimento de cálculo par\ estimar o limite de escoamento no tubo de grande
diâmetro fabricado pelo processo U.O.E. O método foi testado, com bons
resultados, para vários tipos de aços da série API, compreendendo desde os
graus API 5L-X42 até X 70, produzidos comercialmente pela Usiminas - Usinas
Siderúrgicas de Minas Gerais - sendo os tubos fabricados pela Confab Industrial.
Como apoio para este tratamento teórico, as correlações empíricas foram
derivadas das propriedades de tração da chapa original do limite de escoamento
no tubo, com base em análises estatísticas de dados de produção.
11.“Production of plates for large diameter
linepipe in USIMINAS”, 28th Metal Working and Steel Processing Conference,
ISS-AIME, 26-28 Oct. 1986, Pittsburgh, USA.
Abstract
The paper describes
briefly the production facilities available in Usiminas for the manufacture of
high quality plates for API linepipe. Chemical compositions and mechanical
properties of API steels including plate with special characteristicis such as
acicular ferrite grades and steels resistant to hydrogen induced cracking are
presented.
12.“A method of calculating the Bauschinger effect
in API linepipe steels”, 28th Metal Working and Steel Processing Conference,
ISS-AIME, 26-28 oct. 1986, Pittsburgh, USA.
Abstract
Assuming a
stress-strain relation of the form s = Coeno for controlled rolled linepipe steels, empirical
equations are estalished relationg no e Co to the yield
strength and tensile strength of the plate material. Based on these equations a
method is proposed which allows the Bauschinger effect in linepipe steels to be
estimated using conventional plate tensile properties. Application of the
proposed relationship to pipe formed by the U-O-E process is illustrated.
13.“Controle de fratura em
tubos API de grande diâmetro”. 1º CXongresso da Alamet. 3º Colóquio Latino
Americano de Fadiga e Fratura dos Materiais. Rio de Janeiro, 27 Nov. 2 Dez.,
1988, Brasil.
Resumo
O trabalho descreve, a partir de considerações
teóricas e dados da literatura, como ensaios em escala de laboratório - Charpy,
COD (“crack opening displacement”) e DWTT (“Drop weight tear test”) têm sido
usados para caracterizar a inciciação e propagação de fratura frágil em tubos
de grande diâmetro fabricados com aço API de alta resistência. Discute-se
também, resumidamente, a interrupção de fratura dútil em gasodutos de alta
pressão. São apresentados exemplos de procedimentos de cálculo utilizando-se
dados de tubos fabricados ciom aços API
X-70 produzidos pela USIMINAS.
14.“Production of HSLA steels plates in USIMINAS”.
International Conference on Modernization of Steel Rolling. The China Society of
Metals, Beijing, China, April, 1989.
Abastract
A brief descirption
is given of the steelmaking, rolling and plate heat treating facilities. Plate
processing routes and metallurgical features are discussed with particular
reference to ship, linepipe and offchore platform steels as well as high
strength quenched and tempered steels.
15.“Production of Low Alloy Abrasion Resistant
Steels in USIMINAS, 2nd Int. Conf. of HSLA Steels. Oct. 28 - Nov. 2, 1990,.
Beijing, China.
Abstract
This paper deals with
the family of low alloy abrasion resistant steels at USIMINAS. Production and
metallurgical features and mechanical properties of these steels are presented.
16.“Tensile property characteristics of linepipe
steels”, 2nd Int. Conf. of HSLA Steels. Oct. 28 - Nov. 2, 1990,. Beijing,
China.
Abstracts
Tensile properties
commonly specified for linepipe include
the yield strenght (YS), tensile strenght (TS), yield ratio (YS/TS) and the
percent elongation value. Apart from these conventional properties, other characteristics
of the steel, which are usually not reported on a routine basis, such as the
yield point elongation (YPE), work hardening capacity (no) and the
Bauschinger effect can also provide useful information regarding the material
performance. Such properties have been used to characteristize the cold
formability of the steel and to estimate the change in tensile properties,
particulary large diameter pipe. This paper discusses how the work hardening
bahaviour and the Bauschinger effect can be related. through simple statistical
correlations to the conventional tensile properties of the as-rolled plate.
17.“Plate Production Capability at USIMINAS”.
Steel Technology International, 1993, London.
Abstract
The quality and
productivity advantages of continous casting combined with increased capacity
for making clean steel have contributed significantly in upgrading and widening
the plate product range at Usiminas. This has given the company a competitive
edge internationally in the plate sector of the market.
18.“Desenvolvimento de aço
criogênico com 9% de níquel”. Metalurgia e Materiais - ABM, Vol. 49, Nº 414,
Fev. 1993.
Resumo
No trabalho são descritos os principais resultados
obtidos pela Usiminas no desenvolvimento em escala piloto e industrial, de um aço
criogênico baixo carbono com 9% de níquel, laminado em chaps grossas e tratado
termicamente por têmpera e revenimento.
19.“Propriedades mecânicas dos
aços bainíticos baixo carbono microligados com Nb”. Metalurgia e Materiais -
ABM, Vol. 49, Nº 424, Dez. 1993.
Resumo
As propriedades
mecânicas de um aço 0,04C-Mn-Nb-Ti-B, com 12,7mm de espessura
foram avaliadas
para vários teores de Mn (1,40% a 1,80%) e após adição de Ni + Cu ou
Ni + Cr em aço com 1,80% de
Mn. Ss chapas foram testadas na condição de como laminado e após laminado e
após tratamento térmico de revenimento de 600ºC por 70 minutos. O aço bainítico
base (1,80%) apresentou boa combinação de reistência e tenacidade, Um ganho
adicional de resistência ocorreu com a adição de Ni + Cu ou Ni +_ Cu + Cr, sem
grandes influências na tenacidade.Um ganho de resist~encia pode ser obtido pelo
revenimento destes aços, mas os valopres e alongamento tendem a deteriorar.