Jumper layout for Maxtor Durango Series - 71626AP, 71084A/AP, & 7541A Drives
==============================================================================

                        JUMPER DESIGNATIONS
                                            |J24|J23|J20|
      +---------------------------------------------|---+
      | Cable Select                        |   |   |   |
      |  Disabled*                          | O |   |   |
      |  Enabled                            | J |   |   |
      +-------------------------------------------------+
      | Write Cache                         |   |   |   |
      |  Enabled*                           |   | O |   |
      |  Disabled                           |   | J |   |
      +-------------------------------------------------+
      | Master/Slave                        |   |   |   |
      |  Only drive in single drive system* |   |   | J |
      |  Master in dual drive system*       |   |   | J |
      |  Slave in dual drive system         |   |   | O |
      +-------------------------------------------------+
         J=Jumpered O=Open *=Default                      
         Note: Jumpers J21 & J22 are factory reserved, do not use.
         A spare shunt is shipped between J23 & J24.


+----\    /---------------\      /--\   /-------------\      /--\   /--------+
|     ----                 ------    ---               ------    ---         | 
|                                                            +------+     +---+
|                         +--------------------------------> ||:::::|    -|   |
|  +                      V                                  +------+    -|   |
|                +-----------------+                            +        -|   |
|                |   J20 J22 J24   |                                     -|   |
|                |  +-----------+  |                                     -|   |
|                |  | * 0 0 *** |  |                                     -|   |
|                |  | * 0 0 0 0 |  |                                     -|J1 |
|                |  +-----------+  |                                     -|   |
|                |     J21 J23     |                                     -|   |
|                +-----------------+                                     -|   |
|                                                                        -|   |
|                                                                        -|   |
|                                                                       1 |   |
|                                                                         +---|
|                                                                        +----|
|    +                                                              +  1 |    |
|                                                                        |    |
|                                                                        | J2 |
|     ----                 ------    ---               ------    ---     |    |
+----/    \---------------/      \--/   \-------------/      \--/   \----+----+


===============================================================================

Power and IDE interface cable connections:

  |                                    J1                         |
  |      J2        ___________________Data__________________      |
  | ____Power___  |  . . . . . . . . .   . . . . . . . . . .|     |
  |/            \=|  1 . . . . . . . . . . . . . . . . . . .|=====|
  || O  O  O  1 | |___________________   ___________________|     |
  ||____________|                                                 |
  | +5  G  G +12                                                  |
  |===============================================================|
   ===============================================================
       "Back" of typical Maxtor 7000A Series IDE Hard Drive
           Showing Data and Power connector orientation

          Red or Blue stripe on 40 pin ribbon cable=pin 1
          Power cable:  +5=Red  Grounds=Black  +12=Yellow

===============================================================================

The serial number is located on the lower left corner of the Maxtor Label.
This label is located on the side opposite the printed circuit board.
The serial number is also located on a barcoded label on the "front" of 
the drive, and also on the retail box.
The serial number is made up of alpha-numeric charaters, for example: A30025PR

===============================================================================

                            CMOS Configurations:

               Drive     Cyls   Hds  Write  Landing Sec/Trk
                                     PreComp  Zone
               --------------------------------------------
               7541A     1052   16     0       0       63
               71084A/AP 2105   16     0       0       63
               71626AP   3158   16     0       0       63


                        71626A/AP, 71804A, and 7541A
                    are Trademarks of Maxtor Corporation.
               AT is a registered trademark of IBM Corporation.
               Specifications subject to change without notice.
                      Copyright 1995 Maxtor Corporation.
                         Rev A    7/22/95    Anderson

===============================================================================

