===============================================================================
                           71626A/AP IDE DRIVE
===============================================================================

KEY FEATURES:

  * <12ms average seek              * 64K/128K on-board buffer
  * Low power consumption           * Zone density recording 
  * 1:1 interleave                  * Dual drive master/slave support 
  * Rotary voice coil               * Automatic actuator lock 
  * Single-sided surface mount PCBA * 4480 RPM Rotational speed 	     
  * EPA Energy Star compliant       * MaxCache buffer management

SPECIFICATIONS:

Formatted capacity: ........................ 1,629,831,168 Bytes
                                             1,554 Megabytes 
Bytes per sector:........................... 512
Integrated Controller/Interface: ........... AT 
Actuator type: ............................. Rotory Voice Coil
Number of Disks: ........................... 3
Data Surfaces: ............................. 6
Data Heads: ................................ 6
Data Zones per Surface: .................... 10
Servo: ..................................... Embedded
Number of Cylinders (user): ................ 4,086
Sectors per Drive (user): .................. 3,183,264
Track Density (tpi): ....................... 4,232 average
Flux Density (kfci): ....................... 61.42 maximum
Recording Density (kbpi): .................. 92.13 maximum
Encoding Method: ........................... RLL 1,7
Buffer Size: ............................... 128K
Interleave: ................................ 1:1


PERFORMANCE:
Seek performance (including settling time and servo overhead)*

Seek times* (ms)
     Track to track: ....................... 2
     Average: .............................. <12 **
     Maximum: .............................. <25

Spindle speed (+-0.1%): .................... 4840 RPM
Average latency (ms): ...................... 6.7
Controller overhead: ....................... 0.3 ms

Data transfer rate (Mbytes per sec)
  To/From Media (MB/sec): .................. 4.61 - 8.10
  To/from Host (without I/O CHRDY): ........ PIO Mode 3, 11.1MBs
  To/from Host (with I/O CHRDY): ........... PIO Mode 4, 16.6MBs
  DMA Transfers (sustained) ................ Mode 0 w/o DMARQ
  DMA Transfers (burst) .................... Mode 1 with DMARQ

Start time (0 - Drive Ready) 
  Average .................................. <8.5 sec
  Maximum .................................. <20 sec
Stop Time/Power Down: 
  Average .................................. <3 sec
  Maximum .................................. <5 sec


Power Requirements - Two Disk (Average)

    Mode         +12VDC +-8%  +5VDC +-5%  Power/Duration
    ----         -----------  ----------  --------------
    Spin-up        1.02A       317mA         7.95W 
    Read/Write     172mA       437mA         4.25W
    Active         167mA       397mA         3.98W
    Idle           142mA       388mA         3.64W
    Standby        0.95mA      103mA         0.53W
    Sleep          0.96mA       54mA         0.28W

Maximum power supply ripple allowed: 100mV peak to peak, 0-20 MHz

Power Mode Definitions:
-----------------------
Spin-up	    The drive is spining up following initial application 
	    of power and has yet not reached full speed. Maximum
	    current draw lasts 3.8 seconds.

Read/Write  Data is being read or written to the drive.

Active	    The drive is spinning and most circuitry is powered on. 
	    The drive is capable of responding to read commands in
	    the shortest possible time. Read/Write heads are positioned
	    over the data area.

Idle	    The drive is spinning., the actuator is parked and powered
	    off, and all other circuitry is powered on. The drive is 
	    capable of responding to read commands within 40ms.

Standby	    The spin motor is not spinning. The drive will leave this
	    mode upon receipt of a command that requires disk access.
	    The time-out value for this mode is programmable. The
	    buffer is active to accept write data.
	    A program called GREENDRV.ZIP is available on the Maxtor
	    BBS (303-678-2222), that will allow you to program this 
	    delayed standby mode.

Sleep	    This is the lowest power state. The interface becomes 
	    inactive. A software or hareware reset is required to 
	    return the drve to Standby.


Physical:

    Height:  1.00"  ( 25.4 mm)
    Length:  5.75"  (146.1 mm)
    Width:   4.00"  (101.6 mm)
    Weight:  1.2 lb.  (0.5 kg)

Environmental:

Temperature (Degrees C)
    Operating (stabilized).................. 5C to 55C 
                                             Thermal gradient 20C/Hr max
    Non-operating/Storage .................. -40C to 71C
                                             MIL-STD-810E Method 502.3 & 501.3

Humidity ***
    Operating .............................. 5% to 95% non-condensing
    Non-operating/Storage .................. 5% to 95% non-condensing

Thermal Shock
    Low Temperature (-20C to +25C) ......... MIL-STD-810E Method 503.3
    High Temperature & Humidity ............ MIL-STD-810E Method 503.3
    (+35C, 80%RH to +25C, 50%RH)

Altitude (relative to sea level)
    Operating .............................. -200 to 10,000 feet
    Non-operating .......................... MIL-STD-810E Method 503.3
    
Reliability and Maintenance:

    MTBF ................................... >300,000 hours 
    AFR .................................... <=2.9%
    Preventative Maintenance ............... None
    Component design life .................. 5 years (minimum)
    Error Rate ............................. <1 per 10^13 bits read
    Start/Stop Cycles....................... >40,000
    Quality Acceptance Rate ................ 99.8% (2,000 DPPM)

Shock & Vibration (typical):
          
    Operating Shock ........................ 35 Gs, 3ms (no errors)
    Non-Operating Shock .................... 120Gs, 2.5ms (no damage)
    
    Operating Vibration (without non-recoverable errors)
     Per MIL-STD-810E Method 514.4
      10Hz ................................. 0.004 GxG/Hz
      40Hz ................................. 0.004 GxG/Hz
     500Hz ................................. 0.00004 GxG/hz

     Per MIL-STD-810E Method 514.4
      Non-operating Vibration (without non-recoverable errors)
      10Hz ................................. 0.0015 GxG/Hz
      40Hz ................................. 0.0015 GxG/Hz
     500Hz ................................. 0.000015 GxG/hz

    Operating Swept Sine Vibration (1 octave/minute)
      5-20 Hz .............................. 0.049" (double amplitude)
      20-300 Hz ............................ 1.0 G peak

Acoustic Noise:
    Sound power (per ISO 7779) ............. 3.5 dBA
    Loudness (per ISO 532 B) ............... 1.26 sones
    Sharpness (proposed ANSI standard) ..... 1.56 Acums

*   At nominal DC input voltages
**  The average of 10,000 random seek times (measured on independent
    test equipment) constitutes the average seek time specification.
*** Operating and non-operating specs meet MIL-STD-810E. 
    Method 507.3 Table 507.3-I High humidity diurnal category. 
    Natural, High Humidity, Cyclic (Cycle 3)

==============================================================================

                      71626AP JUMPER DESIGNATION
                                            |J24|J23|J20|
      +---------------------------------------------|---+
      | Cable Select                        |   |   |   |
      |  Disabled*                          | O |   |   |
      |  Enabled                            | J |   |   |
      +-------------------------------------------------+
      | Write Cache                         |   |   |   |
      |  Enabled*                           |   | O |   |
      |  Disabled                           |   | J |   |
      +-------------------------------------------------+
      | Master/Slave                        |   |   |   |
      |  Only drive in single drive system* |   |   | J |
      |  Master in dual drive system*       |   |   | J |
      |  Slave in dual drive system         |   |   | O |
      +-------------------------------------------------+
         J=Jumpered O=Open *=Default                      
         Note: Jumpers J21 & J22 are factory reserved, do not use.
         A spare shunt is shipped between J23 & J24.


+----\    /---------------\      /--\   /-------------\      /--\   /--------+
|     ----                 ------    ---               ------    ---         | 
|                                                                         +---+
|                                                            +------+    -|   |
|  +                      V--------------------------------> ||:::::|    -|   |
|                +-----------------+                         +------+    -|   |
|                |     J21 J23     |                            +        -|   |
|                |  +-----------+  |                                     -|   |
|                |  | * 0 0 *** |  |                                     -|   |
|                |  | * 0 0 0 0 |  |                                     -|J1 |
|                |  +-----------+  |                                     -|   |
|                |   J20 J22 J24   |                                     -|   |
|                +-----------------+                                     -|   |
|                                                                        -|   |
|                                                                        -|   |
|                                                                       1 |   |
|                                                                         +---|
|                                                                        +----|
|    +                                                              +  1 |    |
|                                                                      2 |    |
|                                                                      3 | J2 |
|     ----                 ------    ---               ------    ---   4 |    |
+----/    \---------------/      \--/   \-------------/      \--/   \---------+



===============================================================================

Power and IDE interface connections:

  |                                    J1                         |
  |      J2        ___________________Data__________________      |
  | ____Power___  |  . . . . . . . . .   . . . . . . . . . .|     |
  |/            \=|  1 . . . . . . . . . . . . . . . . . . .|=====|
  || O  O  O  1 | |___________________   ___________________|     |
  ||____________|                                                 |
  | +5  G  G +12                                                  |
  |===============================================================|
   ===============================================================
       "Back" of typical Maxtor 7000A Series IDE Hard Drive
           Showing Data and Power connector orientation

          Red or Blue stripe on 40 pin ribbon cable=pin 1
          Power cable:  +5=Red  Grounds=Black  +12=Yellow

===============================================================================

The serial number is located on the lower left corner of the Maxtor Label.
This label is located on the side opposite the printed circuit board.
The serial number is also located on a barcoded label on the "front" of 
the drive, and also on the retail box.
The serial number is made up of alpha-numeric charaters, for example: A30025PR

===============================================================================

                            CMOS Configuration:     

                    Cyls   Hds  Write  Landing Sec/Trk
                                PreComp  Zone
                    ----------------------------------
                    3158   16     0       0       63

                   

                71626AP is a trademark of Maxtor Corporation.
               AT is a registered trademark of IBM Corporation.
               Specifications subject to change without notice.
                      Copyright 1995 Maxtor Corporation.
                        Rev A    7/21/95     T.Brooker

================================================================================
