Full Autodetect and NoSwap modchip with media Autodetect and intuitive PnP Technology.

Based on Secure Antifuse Ex Series ACTEL FPGA. Ex Series ACTEL FPGA is the most SAFE, SECURE and is the LOWEST power consumption (2.5V) device on the market. It is NOT legacy flash based FPGA/CPLD.

Ripper 3 supports up to 4Mb Flash Memory on board for future upgrades and possible application space on chip and features we don’t know about yet :-)

Absolutely new, rewritten VHDL code with Laser and Laser Coil protection routines.

Absolutely new LPPT (Low Power Patching Technique) to save and PROTECT PS2 motherboard.

No more MMF (Mysterious Motherboard Failures).

Reduced power consumption by a factor of 8x. Ripper 3 will not consume too much power from your console, leaving saved power for larger HDD and for more stable operation.

Ground Bounce Free Technology.

Full PAL and USA NTSC Support. PAL V3..V12 and USA V1..V12. Asian revision upgrade will be soon.

No need to press reset once, twice or three times for boot mode selection. Simply insert CD or DVD and AUTODETECT will do everything for you. DVD Video, PS2 and PSX are automatically detected by Ripper 3. You can boot from browser, by closing tray, by joypad selection after entering DEV.olution mode and after returning to browser. BOOT as you want!

No need to remember manual for Ripper3!

Insert and Play Technology.

16MB and 32MB third party memory card support without boot CD for them.

PSX LOGO position and PSX game screen position are PERFECT and FIXED.

Everything is AUTO in Ripper3. NO NEED to enter annoying setup/configuration menus. Ripper3 does everything in it’s intelligence.

HDD (Hard Disc) ATAD patching Support (original HDD or any computer HDD with unlimited size).

Free HDLoader support, you can copy your games to HDD with ATAD support.

DVD Region FREE.
DEV.olution Mode for loading apps from memory card.

Only 17/18 wires to solder for PAL consoles and 17/19 wires for NTSC consoles

RGB FIX for all consoles.
Two Chip disable functions: Press START and then RESET or legacy mode 3x reset for convenience and for old, legacy Ripper2 habits.
On screen DISABLE CHIP message. You will know that chip is disabled.

MacroVision OFF.

ULTRA fast PS2 boot (keep pressed the SELECT button and reset) No more to press anything on JoyPad if you don’t like it.

You can use full automatic features or use legacy Ripper2 booting technique if you like. No need to configure it and all is intuitive without configuration. Ripper3 will automatically predict your needs.

CD/DVD controller requires only 3 wires to be soldered to the bottom of the motherboard.

Only “B”, “G”, “I” wires to the bottom for older PS2 versions.

Less wires to the laser controller and new patching technology = longer laser life and NO LA6508 failures, remember new VHDL code!
Updateable (Re-programmable) Flash Memory Integrated Circuit supports up to 4Mb on chip.

2,5V Very Safe Ripper3 operation and Safe 3,3V power supply.

2.5V Very Safe chip operation for more stable and more SAFE operation. Remember, lower voltage is better!

Ground Bounce effect is _NOT_ existent.

It means very easy install without black screen.

DVD9 compatible.

Action Replay and Action Replay MAX compatible.

Disc swapping supported for CD/R media and DVD/R media.

DivX and MP3 Mediaplayer compatibility.

Fully compatible and tested with all bios revisions.

DVDR booting is very fast and reliable with 100% success.

Absolutely new software suite and only compatible with Ripper3.

New Ripper3 navigator with new fresh look and many new options.

New Ripper3 MediapPlayer v1.51 improved for our chip.

New Ripper3 upgraded Free HDLoader with improved reliability.

All features work the same on all console motherboards from PAL to NTSC.

New look of Ripper3 on blue PCB with gold covered contacts.

LED testing diode is even more reliable and tests more during Ripper3 installation.

- Ripper3.2: Ripper 3.2 is the successor of Ripper3.1! It contains all the features and furthermore we implemented Dual-Layer compatibility so you can now enjoy GT4 in it's full beauty !

Το Ripper 3.2 Chip είναι ένα αρκετά αξιόπιστο τσιπάκι τελευταίας τεχνολογίας από την γνωστή οικογένεια Ripper. Λειτουργεί άψογα και παίζει τα πάντα πολύ άνετα χωρίς να δημιουργεί προβλήματα στο Laser ή την κονσόλα γενικότερα. Συνεργάζεται με ΟΛΕΣ τις εκδόσεις PS2 (v3-12, PAL / NTSC), και διαθέτει δικό του πρόγραμμα πλοηγησής και λειτουργίας! Παίζει άνετα όχι μόνο το GT4 που είναι DVD9 αλλά έχει και περαιτέρω λειτουργίες.