10.695 MHz AM/SSB HOOKUP LIST BY PLL CHASSIS TYPE NOTE: Either the 10.695 MHz or 455 KHz CG can be installed in most AM-only or FM-only radios. If interested, send us an SASE for details. Cybernet PLL02A American & Canadian, PTBM048AOX or PTDM058COX AWA/Thorn 1503, Boman CB950, Cardon Iroquois 40, Colt 480, 485DX, 890, 1000, 1200 (Excalibur), Gemtronics GTX77, G.E. 3-5825A, HyGain 2705 (V), 3108 (VIII), J.C. Penney 981-6247, JIL Citizen MPL-5, SSB-M6, Lafayette Telsat SSB80, SSB120, SSB140, Midland 78-976, Palomar 2900, Pearce-Simpson Super Panther, RCA 14T302, Truetone CYJ4837A-87, Universe 5600: A wire marked “C” runs from the secondary terminal of T10 not going to C111/R88, to a foil pad containing one end of C122 and D12, near T13. Cut this wire and install the CG in series. (IN = T10 end, OUT = C122/D12 end.) Dak Mark X only: Cut gray shielded cable connecting T10/C121 to CFl/D12. Install CG in series. (IN = T10/C121, OUT = CF1/D12) Cybernet PLL02A American, PTBM080/085COX & PTRF004/005DOX G.E. 3-5875A Superbase, Midland 78-574, 78-999, SBE LCBS-4: Remove C279 on RF board. (IN = Q210/T207, 0UT = T208.) Cybernet PLL02A Export, PTBM059COX & PTOS006 or PTSY016AOX Ham Int’l Concorde, Jumbo, Multimode II, HyGain V, Lafayette 1200FM, Major M360, M588: A wire marked “C” runs from the secondary terminal of T10 not going to C111/R88, to a foil pad containing one end of C122 and D12 on the main PTBM059 board, near T13. Cut this wire and install the CG in series. (IN = T10 end, OUT = C122/D12 end.) Cybernet PLL02A Export, PTBM121D4X, PTBM121COX Cobra GTL150, Colt 320DX, 320FM, 1200DX (Excalibur), Ham Int’l Concorde II, HyGain 2795DX, Intek 1200FM, Lafayette HB70AFS,Tristar 747: A wire marked “H” runs from one secondary terminal of T12 (the terminal not going to C116/R90) to the pad marked “I” next to T13 (that contains one end of C120/D14). Remove wire from “I.” (IN = wire from T12, OUT = “I.” (C120/D14 junction next to T13.) Cybernet PLL02A Export, PTBM125A4X or PTBM131A4X Colt 1600DX, 2000DX, HyGain 8795 (V), Lafayette 1800, Major Echo 200, Midland 7001 (export), Pacific 160, Superstar 2000, Tristar 777: Remove C120. (IN = T11/Q19, OUT = T12.) Cybernet PLL02A Export, PTBM133A4X: Ham Int’l Concorde III, Jumbo III, Multimode III. Remove C117. (IN = T11/R96, OUT = T12.) Cybernet PLL02A Export, PCMA001S Argus 5000, Colt 2400, Cobra 148GTL-DX (fake), Falcon 2000, Lafayette 2400FM, Mongoose 2000, Nato 2000, Palomar 2400, 5000, Starfire DX,Superstar 2200, Thunder 2000, Tristar 797, Tristar 848: Remove C120. (IN = T11/Q19, OUT = T12.) Early Uniden µPD2824 PLL SSB Chassis (10.695 MHz IF, PC833, PC965) Cobra 146GTL, Midland 6001/7001 late, 79-260, Pearce-Simpson Super Cheetah, President P300, AR144, AX144, Realistic TRC451,Sears 663.3810, Uniden PC244: Remove C46. (IN = L6, OUT = L7/C47.) Late Uniden µPD2824 SSB Chassis (PB062, PB105, PB122) Realistic TRC453, TRC465, TRC850, Uniden PC122, PC122XL, PRO-640e, PRO-810e: Remove C40. (IN = L8, OUT = R58/D12.) Uniden Multimode Export w/MC145106 PLL, PB010 chassis Cobra 148GTL-DX (late), President Richard, Superstar 360FM: Remove C61. (IN = L11, OUT = L12/C62.) Uniden Multimode Export w/MC145106 PLL, PB042 chassis President Jackson: Remove R74 (470W). (IN = FT4/C16/C17, OUT = R75/TRI3.) Uniden "clone" Multimode Export w/MC145106 PLL, EPT00JA-10Z chassis Superstar Jackson: Remove R74 (470W). (IN = FT4/C16/C17, OUT = R75/TRI3.) Uniden Multimode Export w/MC145106 PLL, PC879 chassis Cobra 148GTL-DX (early): Remove C48. (IN = L6, OUT = L7/C49.) Uniden Multimode Export w/MC145106 PLL, PC893 chassis Stalker 9-FDX, President McKinley export: Remove C57. (IN = L10, OUT = L11/C58.) Uniden Multimode Export w/MC145106 PLL, PC999 chassis President Grant Export: Remove C61. (IN = L11, OUT = L12/C62.) Uniden “clone” multimode copycat models using MC145106 PLL and with EPT3600-10A, -10Z, -11A, 11Z, -13B, -14B or similar Ranger-type chassis. NOTE: If in doubt about your specific chassis, check the other AM/FM “clone” listings below or send us the exact chassis details. Cherokee CBS2100, NR100, NR150, Connex 3300, 3500, Dirland 3300, 3500, 3600, 3700, 3900, Eagle 2000, Excalibur (base), Excalibur Samurai, Galaxy 11B, Galaxy 2100, Galaxy II, Galaxy DX33, DX44, DX55, DX66, DX73V, DX77, DX88, DX99, Galaxy Jupiter, Galaxy Melaka, Galaxy Pluto, Galaxy Saturn, Galaxy Sirius, General Lee, General Stonewall Jackson, Mirage 44, Mirage 6600, Mirage 88, Mirage 9900, Mirage II, Mirage III, Northstar 3000, 4000, 6000, 9000, 9500, President Franklin, Super Galaxy, Superstar Grant, Superstar 3300, 3500, 3600, 3900: Remove C58. (IN = L10, OUT = L11/C59.) European-made version of Uniden "clone" chassis above (same circuit, different part numbers) Euro 3900: Remove C64. (IN = L9, OUT = L11/C65.) Early Uniden “Clone” AM/FM fakes w/MC145106 PLL & EPT3000-10A chassis Dirland/Superstar 3000: Remove C53. (IN = L9, OUT = L10/C54.) Early Uniden “Clone” AM/FM fakes w/MC145106 PLL & EPTMARS-10Z chassis Dirland/Superstar 3500: Best-remove C38. (IN = L6, OUT = Q8/C39/R22.) Also possible but not as effective: replace FL1 (IN = L7, OUT = R26/R27/Q9.) Miscellaneous Newer CB or 10-Meter AM/FM/SSB Chassis NOTE: Increasingly many newer 10M & “export” type multimode/multiband radios are now built using only Surface-Mount Devices (SMD), including the main chassis. Components and spacings are tiny! You'll need a magnifying glass, special miniature solder iron, etc. It’s not practical to use the CG in those models unless you’re an experienced pro with all the right tools and know exactly how to do it. (SMD models noted here where known.) Cherokee CBS-1000: Remove C32. (IN = L33, OUT = L34.) Cobra 150GTL: Remove CF2-1. IN = R91, OUT = CF2-2 Cobra 200GTL: Remove C75. IN = T708, OUT = R93/Q23 for SSB only. NOTE! To also filter on AM/FM, you would need another 10.695 MHz CG in place of their "CF2" monolithic crystal filter. (For that one, IN = R91/R131, OUT = IC1, C622.) Cobra 148FGTL-DX+, Connex 4400, 4800, Galaxy DX45MP, DX48T, DX93T, DX95T, DX2517, General Grant, General Stonewall Jackson, Ranger 99, RCI2960, RCI2980WX, RCI6300, & others w/EPT6900 main PCB: Remove C61.(IN = L8, OUT = L9/C62.) Galaxy DX949, DX959, DX2547, Texas Ranger 396, 399, 696, 699, “900” series & others w/EPT0696 main PCB: Remove C61. (IN = L8, OUT = L9/C62.) Courier Galaxy IV: Remove C30. (IN = T7, OUT= D10/R31.) Courier Galaxy V, VI: Remove C58. (IN = L10, OUT = L11/C59.) Eagle 5000, Galaxy Saturn Turbo, DX-2527, older RCI2950, 2970, 2980, 2990, Sommerkamp TS-2000DX w/EPT2950 main PCB: Remove C72. (IN = L12, OUT = L13/C73.) Emperor TS-5010: Remove C115. (IN = L104, OUT = R304.) G.E. 3-5826A: Remove C55. (IN = T7, OUT = T9.) Magnum 257, 357, 457, Titan II, RPSY-485, ProStar 400, Superstar 4900*: Remove C87. (IN = T8/Q8/R14, OUT = T7) Magnum Delta Force*: Remove C187. (IN = L112/C117, OUT = D124/R204/R206. *NOTE: This is for SSB only; no way to install CG to include AM and FM modes without defeating the Noise Blanker. For AM/FM you can also install our 455 KHz filter in place of the existing 455 "FL101". (IN = Q112/R123, OUT = R124/R136/D107. Midland 79-265: Remove C30. (IN = T7, OUT = R31/D10.) Midland 79-290: Remove C57. (IN = T4, OUT = Q19/R69.) Radio Shack HTX-100: Remove C43. (IN = L5, OUT = R56/D14.) Radio Shack TRC485: Remove C32. (IN = T4/Q4, OUT = T5.) Ranger AR3300, 3500: Remove C24. (IN = R21/C416, OUT = R20/D8.) RCI2950DX, 2970DX, 2985DX, 2990DX, 2995DX w/EPT6950 main PCB: Remove C68. (IN = L8, OUT = L9/C69). WARNING: This has an SMD main chassis; leave this installation to a pro! RCI6900FTB w/EPT9900 main PCB: Remove C68. (IN = L8, OUT = L9/C69). WARNING: This has an SMD main chassis; leave this installation to a pro! Superstar 4900B: Remove C69. (IN = T204, OUT = T205). Uniden HR2510, 2830, President Lincoln: Remove C15. (IN = L115, OUT = D105/R9.) C15 is between L115 and SSB filter FT102. Bend leads 90° and install on foil side of PCB; criss-cross the IN/OUT leads and use the sleeving insulation provided. Put some insulating tape between filter and radio PCB. Uniden HR2600: same as HR2510 above, except IN = L4, OUT = R9/D5.