This parts list is to be used when ordering replacement parts; it contains all
parts for model GL1000K3
I. How to order parts
1 Information required
Replacement parts orders must contain both the part number and he stamped number(s) as
described below. This is because any changes and modifications of parts are registered at
HONDA with the pertinent parts and stamped numbers.
.Numbers needed :
| (a) Carburetor parts: | Part number and Stamped carburetor identification number |
| (b) Engine parts: | Part number and Stamped engine number |
| (c) Frame parts: | Part number and Stamped frame number |
| (d) Final driven: | Part number and gear parts Stamped final driven gear number |
2. Revisions
When modifications additions to this parts list are made, a revised edition will be
issued at an appropriate time, with successively progressing revision numbers on the
cover. We advise to obtain such revisions in order to keep your parts lists up-to at all
times. To check whether a parts list revision has been issued, please contact your HONDA
distributor.
II. How to read this partslist
2. Color code
The color code at the end of the part number indicates the color. Codes below
Color |
code | Color description |
Parts code |
HONDA code | |
| A | White | |
| B | NH-1 | Black |
| XW | Chrome plated | |
| A-01 | Semi glazed Black | |
| PB- 102C-S | Candy grandeur blue special | |
| R 7C-C | Candy limited maroon | |
| PB-2C-S | Candy bleu green | |
| PB-6C-S | Candy cirius bleu | |
| R-6C-S | Candy antares red | |
| R-7C-C | Candy LTD maroon | |
| Y-34 | Sulfur yellow |
3. Abbreviations
The following abbreviations are used in this parts list.
| ASSY.......... | Assembly | KPH........ | Kilometers per hour |
| COMP........ | Complete | MPH....... | Miles per hour |
| R .............. | Right | L(100L)... | Link (100Links) |
| L .............. | Left | A.C........ | Alternating current |
| STD........... | Standard | D C........ | Direct current |
| MM ........... | Millimeter | IN........... | Inlet |
| G............... | Grarn | EX.......... | Exhaust |
| T (22T)........ | Tooth (22Teeth) | FR.......... | Front |
| A................ | Ampere | FIR......... | Rear |
| V ............... | Volt | HEX........ | Hexagonal |
| W.............. | Watt |
4. Dimensions
All dimensions are given in millimeters (mm) except in the case of steel balls, tires and
tire tubes
| Parts | Example | Interpretation |
| Bolt (Screw) | 6x12 | 6mm diameter, 12mm length |
| Pin | 8x14 | 8mm diameter, 14mm length |
| O-Ring | 9.5 x 1.6 | 9 5mm diameter, 1.6mm thickness |
| Oil seal | 14x24x5 | 14mm inside diameter, 24mm outside |
| diameter, 5mm thickness | ||
| Tube | 5x130 | 5mm inside diameter, 1 30mm length |
5. Supersedence of parts
Part numbers given under the part name
in the "Description" column indicate that the part number has been superseded by
that part number. HONDA may make such supersedence without notice.
6. Assemblies
Sections framed with broken lines in the exploded view drawings are available as complete
assemblies. (Their individual parts can also be obtained)
7. Required quantity
The number given in the Reqd. No column indicates the quantity of parts used in the
section described in that block. Parts with quantities in ( ) represent optional parts.
Part whose required number is "N ", is part whose required number can be
selected
at need.
8. Part modifications-applicable serial numbers
In cases where a part has been
modified, the serial number of the first vehicle (or frame, engine,
carburetor, final driven gear) bearing the modification is listed in the "Serial
No.", column.
9. Models, area codes and applicable serial numbers
Models, area codes and applicable serial Nos. given in this parts list can be identified
as follows. Parts with area codes are exclusive for models destined for countries
designated.
If no area codes are listed, parts are for common use.
10. Location of stamped serial numbers.
|
|
|
|